Huge L83 & L86 NA Head & Cam Performance Gains (+100rwhp!)

LT’s are the new LS’s!

The performance truck market continues to grow at a staggering rate – with huge popularity going back to the early LS trucks.

The L83 (5.3L) and L86 (6.2L) performance potential is especially promising due to these modern generation LT engines offering so much more power and technology than its predecessor in a factory trim. For instance, a L83 powered 5.3L truck starts out 50 HP stronger than it’s 5.3 LS counterpart –  giving you a much better starting point with these engines!

That being said – there is always room for improvement right?

Intake Manifold & TB Upgrade (a MUST L83 Upgrade!)


  • Direct L86 Manifold & TB Swap on L83: 9 RWHP / 6 RWTQ
  • Ported L86 Manifold & TB Swap on L83: 17 RWHP / 9 RWTQ

During our R&D process with the L83 (5.3L) engine, we discovered that the intake manifold and throttle body from the L86 (6.2L) was a direct bolt-on application for the L83 (5.3L)! The ports lined up perfectly, with the main difference between the two being: runner length and plenum design.

We immediately picked up 9 RWHP and 6 RWTQ. After noticing great gains in simply bolting on the L86 (6.2L) intake manifold and throttle body, and observing significant obstruction in the manifold stands, we decided to port the intake manifold and test again. (Note that we did not port the throttle body, just the intake manifold.) Testing the ported version, we were able to pick up another 8 RWHP and 3 RWTQ, for a total gain of 17 RWHP and 9 RWTQ!

Camshafts and Install Packages


  • Low Lift Cams: Up to 60 rwhp / 30 rwtq
  • High Lift Cams: Up to 90 RWHP / 45 RWTQ

All of our Direct Injected camshafts incorporate a larger fuel lobe, going with the informal industry standard of 32% larger. We’ve specifically ground these cams to utilize our GPI Phaser Plugs (in either a 4° or 0° block-out).

With our truck cams, we’ve stayed with our proven low-lift cam design. We have found – the majority of our customers want the sound and added power, but still want to retain that 100,000 mile durability. Our low-lift cam grinds are more gentle on valvetrain, yet still offer great gains in power. These low-lift cams are designed to work with the factory pushrods and run on a factory LT1 valve spring.

Of course, we do offer all of these cams in a high-lift version as well, for those seeking an all-out performance build!  The high-lift cams offer the same drivability mannerisms as their low-lift counterparts, but offer an increase in power due to the higher valve lift.


  • L83 Heads: Up to 25 rwhp / 15 rwtq
  • L86 Heads: Up to 30 rwhp / 15 rwtq

When it came to designing a cylinder head package for our L83 (5.3L) truck customers, we kept the ports small in order to emphasize port velocity. This has allowed us to see significant power increases under the curve, not just in the high RPM range.

Our L86 (6.2L) cylinder heads utilize our proven CNC porting program that we run on our LT1 cylinder heads, while we developed a new porting program for the L83 (5.3L) cylinder head.

Several milling options are available, and we highly recommend that piston-to-valve clearance is properly checked in any milled application.

During our porting process, we want to ensure that we provide you – the customer – with the greatest and most reliable product that we can. This is why we install guide liners and precisely grind the liners to achieve optimal valve to guide clearance. All of our cylinder heads also receive a valve job – grinding the valve seats to custom angles. In addition to the cylinder heads being cleaned, deburred, etc., the bowls are hand-blended on every set of cylinder heads.

Torque Converters

Converter Recommendation

  • 258mm Converter for both 6L80 and 8L90 (for most applications)
  • 245mm for all out track builds
  • 3000-5000 stall based on driving style (lower improves street manners / higher improves 60ft times)

When it comes to converter options for the DI trucks, we relied on our history and relationship with Circle D Converters to choose the perfect converter for these applications. As a standard, we recommend a 258mm converter, with stall speeds between 3000-5000 on a “B” stator.

In lighter, race applications, the 245mm converter is still a viable option as well!

Drop-In Pistons (for supercharged / turbo / nitrous applicaitons)

This kit includes:

  • Support up to 1000 RWHP applications
  • 6.125 Compstar Connecting Rods
  • Heavy Duty Pin, Locks, and Ring Package
  • Diamond Pistons with 2618 Forging Material
  • Maintains OE Compression of 11:1
  • Thick Wall, Heavy Duty Wrist Pins
  • No Balancing Required! Drop In Piston and Rod Upgrade!!

Much like our well-known LT1 Drop-in Piston/Rod package, we’ve developed a drop-in package for the 5.3 L83 engine as well! These new pistons will feature a Diamond Racing piston, forged from 2618 alloy, and come complete with pins, clips, rings, and valve reliefs. They will maintain a factory compression ratio of 11:1 and utilize the same Compstar rods as our LT1 package. Of course, all of this will be a zero-balance install for a true drop-in application! Look for this new package in the coming weeks, along with a “how-to” video illustrating the proper way to file-fit the rings!

Recent L83 (5.3L) Build

One one of our recent L83 builds we were able to observe significant performance gains from our L83 (5.3L) cylinder heads, camshaft, and intake manifolds.

On the baseline pull our test truck began with 308 RWHP and 338 RWTQ.

Here’s the complete list of mods:

After completion, we ended with 402 RWHP and 396 RWTQ, for gains of 94/58 respectively. Our peak HP was observed at around 6400 RPMs, with peak TQ at around 4800 RPMs.

Before and After Dyno

L83 Head & Cam (Stage 3) Idle Sound

Rather build a turbo truck?

We’ve got you covered too!

Ready to start building your L83 or L86 GM Truck?

We’d love to help!  If you have any questions – just shoot us an email at or call us at (501) 985-4947!

35 thoughts on “Huge L83 & L86 NA Head & Cam Performance Gains (+100rwhp!)

  1. Dennis Backherms says:

    What would it take to get 450 out of this motor? Would that still be considered a daily driver? What about physically deleting the DOD?

  2. Derek Wendt says:

    What is the total cost after install at your shop for the 402hp setup? I love the sound but tow a 7600lb travel trailer fairly regularly. How would the converter handle that?

    • Ryan Stevens says:

      This setup is more for high performance straighline applications. It is not suitable for towing. You would want to stay with our stage one cam, and stock converter for towing applications.

    • Ryan Stevens says:

      The fact is that the increased displacement would be more beneficial in a truck application because of the substantial increase in torque. From this point you could do the same round of mods and end up over 100 rwhp stronger.

Leave a Reply

Your email address will not be published. Required fields are marked *

Contact US

Have a question about the next step of your build, a product, the status of an order, or anything else?  Here is the place to ask!  I’ll funnel your question to the correct team.

What is Shipping Insurance?

Shipping insurance is a service that may reimburse the cost of parcels that are lost, stolen, and/or damaged in transit.

By selecting and purchasing shipping insurance, your package(s) will be insured through either the carrier or a third-party shipping insurance company. In the event your package is lost, stolen, and/or damaged in transit, Gwatney Performance will initiate a claim with the corresponding shipping insurance company. The shipping insurance company’s investigation process can routinely take six to eight weeks for completion. Upon the determination of the shipping insurance company’s claim investigation in favor of the sender, you will receive either a refund in full or replacement product(s).

If you opt to not select and purchase shipping insurance, no shipping insurance will be added to your package(s). In the event your package is lost, stolen, and/or damaged in transit, it will be the responsibility of the purchaser to pursue recourse through the carrier.

By placing your order, you are agreeing to the terms of our shipping insurance policy.

Shipping insurance is required on all orders over $3,000.

Shipping delays due to parts shortages

The availability of OE and performance parts is becoming a problem for everyone in the industry currently. Please know we are doing the best we can to make sure your parts are ordered and arrive in a timely manner, however, it is not uncommon to wait 4-8 weeks or more in some instances for parts currently.

Please note – if it is in stock it will ship quickly. If the part is out of stock, it will be fulfilled on a first come first served basis – based on availability at a supplier level.

We could not be more thankful for all the new customers trusting us with their business and all the faithful repeat customers that keep coming back. We have never been as busy as we currently are, and are doing our very best to keep everyone in the loop and get parts to you as fast as we possibly can!

Please email if you have questions on order status updates:

Thank you all!

Contact Form

Thank you for contacting us!

Your message have been received.  We will message you back as soon as we have the first free moment!


Affirm and Gwatney Performance have teamed up to offer easy financing for orders over $500 – without a catch. There are no gimmicks like deferred interest or hidden fees, so the total you see at checkout is always what you’ll actually pay.


Affirm designed its loans to offer you flexibility and control over your budget. Affirm offers rates from as low as 10-30% APR based on your credit. Actual rates will be shown at checkout.


Affirm has a dedicated team in San Francisco at Affirm HQ, ready to answer your questions and help out however they can.





  1. Be 18 years or older (19 years or older in Alabama or if you’re a ward of the state in Nebraska).
  2. Provide a valid U.S. or APO/FPO/DPO home address. Buy with Affirm is not currently available to West Virginia residents.
  3. Provide a valid U.S. mobile or VoIP number and agree to receive SMS texts. The phone account must be registered in your name.
  4. Provide your full name, email address, date of birth, and the last 4 digits of your social security number to help us verify your identity.


Unlike a credit card, Affirm is not a revolving line of credit. While customers can take out multiple Affirm loans at once, each Affirm loan application is evaluated separately as a closed-end transaction. An application from a returning customer may be denied, however, if that customer has failed to repay other Affirm loans on time or if the customer shows excessive borrowing behavior.


You can pay your Affirm bills online at They accept payment by debit card, bank transfer and check.


Yes, when you first create an Affirm account, Affirm perform a ‘soft’ credit check to help verify your identity and determine your eligibility for financing. This ‘soft’ credit check will not affect your credit score.


Affirms tries hard to approve every purchase but sometimes can’t approve the full amount. When this happens, Affirm provides a debit card down payment option so that you may still complete your purchase right away.


Affirm sometimes requires additional information to consider a credit application. Such information may include an active checking account, which helps Affirm verify your identity and your ability to repay the requested loan. If they prompt you for this information but you are unable to provide it, Affirm will be unable to approve your credit application.

See All FAQs